Gate Opener Repair of Tampa Bay - Driveway Gates, Gate Opener

Gate opener installation

Install / December 25, 2016

Your Guide to Installing a Swing Gate OpenerSwing gate openers are typically battery-operated systems with a low voltage, and they are safe and affordable options for most homes. A transformer often maintains the battery charge, but in some cases, solar panels are used. It is important for users to read the instruction manuals included with the gate opener system, as they provide specific instructions on what type of battery or solar panel is required for each setup. In most cases, no electricians or professional welders are required in the installation process of a swing gate operator. With the right tools and directions, a buyer can install one at home in just a few hours.

Things to Consider Before Beginning the Installation

Before starting the installation, it is important to look at the manual included in the manufacturer package. Automatic swing gate openers use a lot of force, so it is crucial for people to review the safety instructions for each specific model. This helps avoid any potential hazard during or after installation. A buyer should also verify that the swing operator purchased is suited for their specific gate's size, weight, and class rating.

Preparing the Gate for Installation

Gate openers only perform as well as the gates they are opening. Ensure that the swing, level, and plumb of the gate are free on their hinges and not rusty or damaged. The gate should fully open without dragging on the ground. If a gate weighs over 250 pounds, then it should have bearings for security purposes.

Materials Required

Collect all the required materials before starting the installation.

Item

Description

For turning opener screws

Used for boring drill holes

Level

To measure horizontal surface

Used for measurements

C-Clamps

To keep assembly in place

For tightening bolts and nuts

Needed to get power to the control box

Used to provide power, based on specific model

Push Open Brackets

For installing bracket assembly

Gate Attachment Bracket

Needed for gate reinforcement

Fork Lugs

To run electricity

PVC Conduit

To protect and route wiring

eBay offers all of the materials needed for the proper installation of a swing gate opener.

Installing the Swing Gate Opener

There are six basic steps to installing a swing gate opener.

Step One: Define Gate Opener Position and Install the Post Bracket

Do not install the gate opener on the outside of the gate where the public can easily access it. It should be positioned near the inside center line of the gate. This helps minimize the twisting of the gate when the opener is on.

Once the gate is in position, it is time to assemble the post bracket. This assembly creates a space between the operator and the actual gate. To begin, attach the bracket to the front of the opener. Open the gate, and fully extract the opener arm. Adjust the bracket to level, and use the c-clamps to fix the assembly in place.

Step Two: Install the Opener Arm and Stop Plates

Install the opener arm to the post bracket assembly. Verify that it is on level.

The stop plate helps stabilize the gates when they are closed. Detach the opener arm and close the gate. Move the plates into their correct positions and tighten their bolts securely, then open the gate again and install the arm.

Step Three: Set Up the Control Box

This step is optional, because not all models have control boxes.

Place the control box three feet above the floor in order to protect it from weather damages. It should be close to an AC power line as well. Remove the cover from the box and insert the proper power cables using the correct color combinations.

Step Four: Connect Power Cables and Transformer/Solar Panel

After inserting the power cables into the control box and attaching the wires to the proper terminals, install either a transformer or solar panel, depending on the model, to keep the charge going. Do not connect both a solar panel and transformer at the same time, as it can damage the gate opener's control box. Refer to the user's manual to determine which of these two is appropriate.

Step Five: Install the Battery

Most gate openers include their own batteries. Attach the battery to the proper wires on the terminal.

Step Six: Adjust Opener Settings

Refer to the manual in order to adjust warning signs, transmitter settings, auto-close timing, position limit, and stall force. Adjust these options based on the weight and size of the gate.

How to Buy Swing Gate Openers on eBay

eBay sellers offer a variety of swing gate openers. New and used models are available; when buying a used opener, buyers should read the full description of the unit to make sure that all of the parts, including batteries and cables, are included in the package. A user can search eBay using the search bar, which makes locating the correct gate opener quite easy.

Installing a swing gate opener is relatively simple if a consumer follows the correct instructions. For safety purposes, it is important to always read the precautions in the unit's manual, as these are electrical systems and accidents can happen.

Source: www.ebay.com

CATEGORIES